CLUZ 2.0 Firmware

Firmware Update

Current Version: 5.13.08 (build 2442)

• Firmware is accessible from the Object Manager tool.

Installation and start-up process

Changelog

v5.13.08 (build 2442)

25 November 2024

• I/O MODULE 2/2 in version 2.0.2 and I/O MODULE 8/8 in version 2.0.2 - improvement in the area of ​​device communication on the TF-Bus bus (problem with the disappearing module).
• Improved operation of CLU Discovery process.

v5.13.07 (build 2436)

17 September 2024

• Support for modules: GRENTON ROLLER SHUTTER Z-Wave, RELAY X2 Z-Wave, GRENTON LED RGBW Z-Wave.
• Support for modules: INFIBITY DOOR & WINDOW SENSOR Z-Wave, INFIBITY MOTION SENSOR Z-Wave, INFIBITY WATER LEAK SENSOR Z-Wave modules, INFIBITY RADIATOR THERMOSTAT Z-Wave.
• Support for the GRENTON RS232 CONTROLLER.
• System configuration of electrical network parameters for modules: Relay x4 DIN (fw. 2.0.0-2325), Relay x2 DIN (fw. 2.0.0-2325), I/O 8/8 DIN (fw. 2.0.0-2325), I/O 2/2 FM(fw. 2.0.0-2325).
• DALI Controller DIN version 1.1.16 - fix communication problem with module after CLU's update.
• Roller Shutter x1 DIN, Roller Shutter x3 DIN and Roller Shutter FM version 3.2.4 - improvement in the area of device persistence.
• Persistence of user features.
• Added time zones: Kolkata, Tehran, Riyadh, Lagos, Johannesburg.
• Added information about downloading NTP time to system logs.
• New virtual object MultiFanACThermostat(object for fan coil units):
  • Support for 1 to 3 fan speeds,
  • Fan operation in continuous or automatic mode,
  • Thermostat operation in cooling or heating mode,
  • Control of the delay in turning on or off the control output in relation to the fan output,
  • Compressor protection against too frequent switching on.

• Adding new methods for the CLU object:
  • StartZWaveExclusion - initiates Z-Wave module exclusion mode,
  • StopZWaveExclusion - stops Z-Wave module exclusion mode.

• Updated StartZWaveDiscovery method - the command name has been changed to StartZwaveInclusion and the Unlimited option has been added for the Time parameter - the addition process is active until the Z-Wave module is added.
• Adding a new feature for the CLU object ZWaveRouting - sets the possibility of using routing when sending commands from the CLU to the Z-Wave module. By default, the ZWaveRouting feature is set to Off.
• Added new features and methods for the ZWAVE_CONFIG object of the GRENTON RELAY X2 Z-Wave, GRENTON ROLLER SHUTTER Z-Wave, GRENTON LED RGBW Z-Wave, INFIBITY DOOR & WINDOW SENSOR Z-Wave, INFIBITY MOTION SENSOR Z-Wave, INFIBITY WATER LEAK SENSOR Z-Wave, INFIBITY RADIATOR THERMOSTAT Z-Wave:
  • Repeaters - number of devices intermediating in communication between CLUZ and a given module,
  • RepeatersList - list of devices (NodeID) intermediating in communication between CLUZ and the module,
  • UpdateNeighbours - triggers the action of updating and rebuilding the Z-Wave network (number of neighboring modules, method of communication with CLUZ) for a given module.

• Added a new feature for the ZWAVE_CONFIG object of GRENTON RELAY X2 Z-Wave, GRENTON ROLLER SHUTTER Z-Wave, GRENTON LED RGBW Z-WAVE modules:
  • Standalone - setting a rigid connection between the states of inputs and outputs in the module - control without communication with the CLU (a detailed description of the operation of the Standalone mode can be found in the technical documentation of the module).

• Added a new feature for the ZWAVE_DIN objects of the GRENTON RELAY X2 Z-Wave module:
  • Standalone - Sets the internal connection between the given input and the specified output: -1 - default setting, 0 - disabled, 1 - input coupled to the OUT1 output, 2 - input coupled to the OUT2 output.

• Added queuing of Get/Set/SetDefault commands sent to Z-Wave battery modules - sending configuration parameters from the ZWAVE_CONFIG object takes place after the next wake-up of the battery module, not when the method is called.
• Adding a new state "N/A" for the Value feature in the ZWAVE_CONFIG object - displayed when the value of a given register has not been retrieved.
• Support for Z-Wave Aeotec Smart Switch 7.
• Support for Z-Wave Fakro: ZWMR24, ZWS230, ARZ ZWR and AMZ ZWM.
• Removal of a regression introduced in version 5.12 which resulted in sporadic disappearance of TF-Bus devices (voltage restart required to restore module operation).
• Removal of the mechanism for banning Z-Wave devices. The Banned feature remains in ZWAVE_CONFIG objects to maintain backward compatibility.
• Improvement of event generation of SunriseSunsetCalendar.
• Improvement of cloud connection.
• Improvement of diagnostic logs.
• Improved stability of Z-Wave devices.

v5.10.03 (build 2248)

5 December 2022

• Support for diagnostic logging using telnet. Added new method (SetTelnetLogLevel) and feature (TelnetLogLevel) for setting log level.

• Support for Roller Shutter x1 DIN in 3.2.4 version:
  • Maintaining the value of the Position and LamelPosition features after restart (persistence),
  • Additional protection against too short time intervals,
  • Improvement in the area of device persistence,
  • Stability improvements and bug fixes.

• Support for Roller Shutter x3 DIN and Roller Shutter FM in 3.2.4 version:
  • Maintaining the value of the Position and LamelPosition features after restart (persistence),
  • Reversing of Roller Shutter direction,
  • Reversing of range of shutter position (0-100% for 100-0%),
  • Compensation of shutter actuation time,
  • Features that determine the upward and downward movement time of the roller shutter,
  • State of Roller Shutter calibration,
  • Option to specify target lamel position for SetPosition method - Default (lamel position in line with the roller movement), Previous (previous lamel position) or chosen by user,
  • Option for Calibration direction,
  • New events OnPositionChanged and OnLamelPositionChange,
  • Additional protection against too short time intervals,
  • Improvement in the area of device persistence,
  • Stability improvements and bug fixes.

• Support for Z-Wave Aeotec Dual Nano Switch ZW132-C module.

• Improvement of Thermostat virtual object:
  • Fixed generation of OnOutOn, OnOutOff oraz OnChange events,
  • Optimized ControlOutValue change time.

• Improvement of Presence Sensor virtual object:
  • Changed of behavior after object locking,
  • TimeFromLastPresence counts if movement is detected or object is locked.

• Improved State feature of CLU module,
• Improved state of module after firmware upgrade.
• Improvement of the TFBus module communication mechanism.

v5.09.02 (build 2208)

17 August 2022

• Support for the Roller Shutter x1 module in version 3.1.3 - improved settings of the lamel position.

29 March 2022

• Support for Multisensor module:
  • IR transceiver/receiver,
  • Temperature sensor,
  • Air humidity sensor,
  • Atmospheric pressure sensor,
  • Light sensor,
  • Sound sensor,
  • Air CO2 sensor,
  • Air VOC sensor.

• Support for Roller Shutter x1 in 3.1.2 version:
  • Reversing of Roller Shutter direction,
  • Reversing of range of shutter position (0-100% for 100-0%),
  • Compensation of shutter actuation time,
  • Features that determine the upward and downward movement time of the roller shutter,
  • State of Roller Shutter calibration,
  • Option to specify target lamel position for SetPosition method - Default (lamel position in line with the roller movement), Previous (previous lamel position) or chosen by user,
  • Option for Calibration direction,
  • New events OnPositionChanged and OnLamelPositionChange.

• New virtual object - Event Scheduler:
  • Ability to set events in the system that will be triggered based on the applied CRON.

• Sunrise Sunset Calendar:
  • Features informing about the next sunrise/sunset,
  • Feature informing about whether it is currently day or night,
  • Features providing sunrise / sunset times as unix and local time,
  • Ability to add an offset to the event before and after sunrise and sunset.

• Presence Sensor:
  • 2 modes of presence sensor: impulse and state mode,
  • This function allows the operation of a Presence Sensor object with a switch.

• New event OnTimeChange in CLU.

v5.08.01 (build 2128B)

08 November 2021

• Support for Smart Panel V6.

• Support for Roller Shutter x3 in 2.1.3 version:
  • Percentage value of the shutter opening (0 - 100%).
  • Roller shutter lamel position (0° - 90°).
  • Method for roller shutter calibration.
  • Option to Enable / disable the ability to control the roller shutter.
  • OnLamelOpen and OnLamelClosed event.

• Stability improvements for modules:
  • Analog IN/OUT DIN in 1.2.13 version.
  • Digital IN DIN in 1.2.14 version.
  • I/O Module DIN in 1.4.11 version.
  • LED RGBW DIN in 1.4.7 version.
  • Relay 2HP DIN / Relay 4HP DIN in 1.3.13 version.
  • I/O Module FM in 1.1.9 version.
  • Roller Shutter FM in 2.1.3 version.

• Support for Z-Wave Aeotec Nano Shutter v3.04 module.

v5.07.02 (build 2120C)

16 June 2021

• Support for New Virtual Objects - SunriseSunsetCalendar, PresenceSensor.
• Add features responsible for monitoring the CLU supply voltage - BusVoltage, BusVoltageSensitivity, MaxBusVoltage, MinBusVoltage.
• Add features for setting an DNS server address - PrimaryDNS / SecondaryDNS.
• Support for Aeotec Nano Switch ZW139-C.
• Support for OM diagnostic view.
• Support for ROLLER SHUTTER x1 DIN and ROLLER SHUTTER FM in 2.1.2 version:
  • Percentage value of the shutter opening (0 - 100%).
  • Roller shutter lamel position (0° - 90°).
  • Support for operation of roller shutters in the range of 0-600 seconds.
  • Method for roller shutter calibration.
  • Option to Enable / disable the ability to control the roller shutter.
  • OnLamelOpen and OnLamelClosed event.

v5.06.04 (build 2050)

16 December 2020

• Support for New TFBus module - DALI CONTROLLER DIN.
• Support for New TFBus module - ROLLER SHUTTER x3 DIN.
• Stability improvements and bug fixes.

v5.06.03 (build 2043)

26 October 2020

• Support for new Z-Wave modules - enables cooperation with the following Z-Wave modules in the given range:

• New embedded feature for CLU - QoS - Setting the quality level of network services.
• Handling requests for user features from mobile application.
• Increase the stability of communication with mobile application and OM.
• Added default PUSH notification title - "Grenton notification".
• Improvement of Discovery mechanism for 1.0 modules.
• Improvement of the TFBus module updater mechanism.
• Improvement of the PUSH notification mechanism.
• Improving time zone settings.

v5.05.05 (build 2014)

24 April 2020

• New virtual object Push – object enabling configuration of sending push notifications to mobile devices with the myGrenton application. It is possible to create up to 64 virtual objects. It has an implemented queue system that allows you to send a notification at a specified time interval (a maximum of 10 notifications can be queued per Push object).
  • New methods / features for Push object:
    • (Set)Message, (Set)Title – allows to set the content of the header and the message of the notification.
    • ClearMessage, ClearTitle – clears title and message buffer.
    • Send – sends push notification.
    • (Set)Interval – interval between push notifications.
    • LastTimeSend – return send time of last push notification.
  • New events for Push object:
    • OnSend – occurs when a push notification is sent.
    • OnOverflow – occurs when the outgoing buffer overflows.

• Unification for module serial number in config,json file.
• Support for new Heiman Smoke Sensor module.
• Roller Shutter module: State are set by slave device report.
• Getting Hardware Version from TFBus modules.
• Stability improvements and bug fixes.

v5.04.14 (build 2009)

26 February 2020

• Cloud connection stability improvements.

v5.04.11 (build 1949A)

11 December 2019

• CLU time setting using the NTP server including time zone and time change (winter/summer). The time is automatically synchronized with the NTP server. Two new CLUZ features are used for configuration:
  • NTPServer – allows you to enter an IP address (or domain name, eg.: pool.ntp.org) of an NTP server,
  • TimeZone – setting the CLUZ time zone - 22 zones are available.

• The ability to change the voltage and frequency values used by the 2.0 series modules to measure the current/instantaneous power of the receiver. New features are used for configuration:
• DefaultVoltageValue – default value of voltage defined in devices,
• VoltageFrequency - voltage frequency in the power grid.

• Support for new Z-Wave modules - enables cooperation with the following Z-Wave modules in the given range:

• Support for Aeotec Multisensor 6.
• myGrenton Application: o Increasing the buffer for connection to the cloud, o Reporting on value changes for:
  • User features,
  • features of the Calendar virtual object,
  • features of the Schedule virtual object,
  • features of the PID virtual object,
  • features of the Timer virtual object.
  • Analog In/Out - Unification of OnSwitchOn event generation for the AnalogIn and AnalogOut objects .
  • System stability improvements.

v5.03.06 (build 1927A)

08 July 2019

• Support for remote CLU connection to the Grenton cloud via the myGrenton application interface.
• New CLU features:
  • UseCloud - allows you to attach a connection to the cloud,
  • cloudConnection - specifies the CLU connection status from the cloud.
  • Support for new Grenton 2.0 modules - support for all currently sold Grenton 2.0 modules.
  • New CLU update mechanism - allows you to update both the Z-Wave CLU as well as the Grenton 2.0 modules.
  • Assigning numbers to Z-Wave objects with the same SN in different CLUs - adding the homeID of a given CLU to the name of the Z-Wave object.
  • Assigning an IP address when a given address is taken or 2 CLUs have the same addresses.